Error Code KOBELCO for SK200-8 Excavators

 · 
Error Code KOBELCO for SK200-8 Excavators

If there is malfunction for kobelco SK200-8 excavator, there will be error codes showed on the monitor gauge cluster panel. If you do not understand the meaning of these error codes, the machine will be in severe abnormal operation. Even the excavator will be scraped if you do not care about it.

For easier understanding of these error codes, dealing with the faulty machine timely and replacing proper parts to ensure the normal operation of the excavator, we would like to introduce you the error code shown on the
 gauge monitor panel of SK200-8. We hope that it will be helpful.

 

Error Code KOBELCO SK200-8

1. (Engine systems) Sensor systems:

P2228, the atmospheric pressure sensor fault (LO).
P2229, the atmospheric pressure sensor fault (HI).
P0192, rail pressure sensor fault (LO).
P0193, rail pressure sensor fault (HI).
P0191, rail pressure sensor failure.
P0237, boost sensor fault (LO).
P0108, boost sensor fault (HI).
P0117, the water temperature sensor fault (LO).
P0118, the water temperature sensor fault (HI).
P0182, fuel temperature sensor fault (LO).
P0183, fuel temperature sensor fault (HI).
P0335, the main speed sensor system failure, the engine will not start / stop the engine.
P0340, deputy speed sensor system failure, the engine will not start / stop the engine.
P2120, dual throttle sensor system failures, speed down (idling speed 800r / min).
P2121, a throttle sensor voltage is abnormal. P2122, a throttle sensor failure (LO).
P2123, a throttle sensor failure (HI).
P2126, throttle sensor 2 voltage is abnormal.
P2127, throttle sensor 2 fault (LO).
P2128, throttle sensor 2 fault (HI).

 

2. Switches, relays, system fault codes:

P0540, preheating device failure (open circuit / CND shorted).
P0540, preheating device failure (+ B short circuit).
P0617, the start switch circuit failure.
P0686, the main relay circuit failure.
Fuel pump system failure code:
P0629, the fuel supply solenoid circuit fault (+ B short-circuit), the engine can not start / stop the engine.
P0628, fuel pump solenoid circuit fault (full output mode), the output decline.
P2635, history of abnormal pressure fuel pump.
P2635, fuel pump solenoid valve stuck.
P0088, rail pressure abnormalities, output declined.

 

3. Fuel injection system fault codes:

P1211, injector rail a solenoid valve drive system fault (GND short circuit), the output decline on / off cylinders (1, 4).
P1214 Injector solenoid valve drive system common rail 2 fault (GND short circuit), the output decline on / off cylinder operation (two times, three times).
P1212, injector rail a solenoid valve drive system failures (+ short-circuit B / open circuit), the output decline on / off cylinders (1, 4).
P1215, injector solenoid valve drive system common rail 2 failures (+ short-circuit B / open circuit), the output decline on / off cylinder operation (two times, three times).
P1601, multi-point fuel injector correction exceptions, output declined.
P0201, injector solenoid valve circuit breaker, output drops on / off cylinder operation (1).
P0202, solenoid injector 2 circuit breaker, output drops on / off cylinder operation (two times).
P0203, solenoid injector 3 circuit breaker, output drops on / off cylinder operation (three times).
P0204, solenoid injector 4 circuit breaker, output drops on / off cylinder operation (four times).
P0263, cylinder correction fault 1.
P0266, cylinder correction fault 2.
P0269, cylinder correction failure 3.
P0272, cylinder correction failure 4.

 

4. EGR System:

P0489, EGR valve is a linear solenoid valve malfunction (open circuit / GND short circuit), the output decline.
P0490, EGR valve is a linear solenoid valve malfunction (VB short circuit), the output decline.
P0404, EGR valve is stuck in an output drop.
P0405, EGR valve is a safety sensor fault (LO).
P0406, a safety sensor valve failure (HI).
Turbine system fault code:
P0234, turbo too large, the output decreases.
Engine system (state judge) fault code:
P0217, overheating, output declined.
P0219, the engine coaster. Communication: U1001, CAN communication interruption (vehicle).

 

5. ECU system:

P0611, ECU poor charging circuit (LO), the output decline.
P0200, ECU poor charging circuit (HI).
P0605, ROM exception.
P0606, CPU failure, the engine will not start the engine stopped.
P0607, CPU monitoring IC exceptions, output declined.

If you need any help, please feel free to contact us and we will reach out to you as soon as possible.

How to change kobelco SK-8 gauge language? https://www.youtube.com/watch?v=OTz1aOgmQP8

SHOP NOW

Leave a comment

Please note, comments need to be approved before they are published.

RECENT POSTS
RELATED POSTS

Featured Products

60100000 VOE60100000 Engine ECU for Volvo Excavators Loaders Graders - Sinocmp 60100000 VOE60100000 Engine ECU for Volvo Excavators Loaders Graders - Sinocmp
14518349 V-ECU Engine Controller_01 14518349 V-ECU Engine Controller_02
21695313 ECU Engine Controller_01 21695313 ECU Engine Controller_02
Controller Controller

Controller

As the brain behind the machine's operations, the controllers provide essential information and let you stay informed about operating parameters of your machine.

When choosing SINOCMP for your excavator controller needs, you can always expect:

Free Programming: We charge no fees for programming. All you need to do is offer the part number and VIN necessary to us.

Affordable Price: Our ECM controllers are offered in different conditions and pricing for you to choose, from genuine refurbished to aftermarket, all accessible and affordable without compromising on quality.

Hassle-Free Return & Refund: Besides a 12-month warranty, we also offer responsive and efficient return and exchange to ensure your pleasant shopping experience with us.

Shop Controller